Directions:

Preparing the Surface:

• Be sure that the surface is free from loose debris and sediment.
• Dust/dry mop the floor at least two times daily.

Floor Surfaces:

Polishing with an Automatic Scrubber:

• Dust mop the surface using a STONEGLIDE Dust Mop.
• Remove all topical coatings with STONE STRIPPER. (Solvent based coatings must be removed with a solvent based stripper.)
• Wet mop the stone surface using MARBALEX.
• Install a hogs hair or a white pad to the drive pad of the machine.
• Generously spray water to the floor surface not to exceed a 16 square foot area.
• Sprinkle an SCI POWDER on to the wet surface.
  *(One tablespoon of powder per 16 square feet)
  *If using MARBACREAM instead of the powder:
  Begin following steps 1-4. It is not necessary to apply water to the floor surface first. Simply apply 3 inches of MARBACREAM to the surface,spray water over the Marbacream, and begin buffing directly in to the floor. Buff until the haze is completely gone and the shine appears on the floor.
• Proceed forward and backward with the scrubber staying within the perimeter of the wet area.
• Use a squeegee to move the loose paste off of the work surface to see if the desired polish has developed. If it has not, push the paste back onto the work area.
• Continue the buffing motion until the desired polish appears. (DO NOT BUFF AREA FOR MORE THAN THREE MINUTES)
• Extract the paste with the scrubber vacuum.
• Rinse with MARBALEX to neutralize any residues.
• Buff with a clean and soft white polishing pad.
  *For heavily worn surfaces, HONEX HONING POWDER must be used to smooth the surface prior to using the polishing powder.

Polishing with a Manual 175 RPM Buffing Machine:

• Dust mop the surface using a STONEGLIDE Dust Mop.
• Remove all topical coatings with STONE STRIPPER. (Solvent based strippers must be removed with a solvent based stripper.)
• Wet mop the stone surface using MARBALEX.
• Install a soft white polishing pad to the drive pad of the machine.
• Generously spray water to the floor surface not to exceed a 16 square foot area.
• Sprinkle SCI POWDER on to the wet surface creating a loose paste.
  *(One tablespoon of powder per 16 square feet.)
  *If using MARBACREAM instead of the powder:
  Begin following steps 1-4. It is not necessary to apply water to the floor surface first. Simply apply 3 inches of MARBACREAM to the surface,spray water over the Marbacream, and begin buffing directly in to the floor. Buff until the haze is completely gone and the shine appears on the floor.
• Proceed by operating the machine in a left to right sideward pattern completing 4 to 6 passes per section. This will change the powder and water mixture into a loose paste. Stay within the perimeter of the wet area.
• After completing the initial passes, apply a fresh and dry white pad on to the machine and buff the paste directly into the surface. (DO NOT BUFF AN AREA FOR MORE THAN THREE MINUTES)
• As the haze begins to dry, spray more water to reduce the friction of the machine. Buff until the haze is completely gone.
• Rinse with MARBALEX to remove any remaining residue.
• Buff with a clean and soft white buffing pad.
  *For heavily worn surfaces, HONEX HONING POWDER must be used to smooth the surface prior to using the polishing powder.
  **For Polishing Granite Surfaces, Follow The Above Procedures Using An SCI Granite Powder with a hogs hair pad.*

Tabletops, Vanities, Walls and Columns:

• Remove loose debris from the stone surface and spray clean with MARBAMIST.
• Strip off any remaining topical coating.
• Cover all wall coverings and carpeted areas.
• Use a white felt pad on the hand machine or use a damp terry cloth towel when polishing by hand.
• Spray water onto the surface.
• Sprinkle SCI POWDER onto the water to create a paste.
• Begin buffing by hand in a circular motion for 30 seconds or use a hand machine at LOW RPM keeping the surface moist at all times.
• Remove the paste with a squeegee before it dries to see if the desired polish has appeared. If not, push the paste back onto the surface and begin polishing again until the polish occurs. (Buffing action may take thirty seconds to three minutes to create a shine or repair an etch.)
• Rinse the surface with MARBAMIST and let it set for one minute to neutralize the residue.
• Wipe off the MARBAMIST with a clean soft cloth.
• Heavily worn and scratched surfaces should be polished with a thicker slurry.
• Protect the surface with an application of INTERNATIONAL STONE POLISH.

Recommendations:

• Always test on a small area before using to determine if the product is applicable.
• Test Area: Apply the SCI-M2 MARBLE POWDER to a small area at the project site in accordance to the manufacturer's directions on the bottle label. Be sure to record all the test results including coverage and stain prevention.
• Natural stone should be protected with STONE SPRAY-N-SEAL penetrating sealer.
• Follow the recommended SCI cleaning procedures for MARBALEX & MARBAMIST.
• If heavy abrasions or scratches are on the surface, use HONEX prior to using the polishing powder.
• While in the container, SCI-M2 buffing compound may absorb moisture and become hard. This will not affect the performance of the product.
• Cover all surfaces that are not stone.
• Always wear protective clothing such as safety goggles, gloves, and footwear.

Approximate Sq. Ft. Per Pound Coverage:

• Marble 600 sq. ft.
• Agglomerates 600 sq. ft.
• Terrazzo 600 sq. ft.

Applications:

• Marble Floors
• Marble Agglomerates
• Marble Terrazzo
• Marble Vanities
• Marble Tabletops
• Marble Walls

Textures/Surfaces:

• Polished
• Honed

Benefits:

• Repolishes sensitive marble surfaces quickly.
• Simple to use.
• Can be used by hand or machine.
• For commercial and residential use.

Technical Data:

• Powdered Formula
• Polishing Abrasives
• Non-Flammable
• Use with water
• Low Acid

Product Warranty:

SCI guarantees complete satisfaction of its products. If not completely satisfied with the performance of the product, when used as directed and the surface has been tested first, contact Stone Care International, Inc. for a refund of the purchase price or a replacement by another SCI product. Determining the suitability of the product for any intended purpose shall be solely the responsibility of the user. There are no warranties, express or implied, including those of merchantability or fitness for particular purpose which extend beyond the description on the product label.

First Aid

• Eyes: Flush immediately with water; call physician immediately. Obtain medical attention if severe irritation occurs.
• Skin: Remove contaminated clothing. Wash with soap and water; rinse thoroughly; call physician if symptoms persist.
• Inhalation: Remove victim from area of exposure to fresh air; call physician if symptoms persist. If not breathing give artificial respiration and seek medical attention.
• Ingestion: Dilute by drinking large amounts of water. Repeat at least once and then administer milk of magnesia as an emollient. Do not induce vomiting. Obtain medical attention immediately.